Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 162

background image

APPX

Appendix 2 Remote Registers

141

A

• When "Without initial processing" is set
Initial processing request flag (RWr0.b8) does not turn on. The IO-Link module becomes operable (the update of external I/O
becomes enabled) without Initial processing completion flag (RWw0.b8) being turned on. When the module is powered on,
Remote READY (RWr0.b11) turns on.
Module parameter settings are read from the data storage.

*3 When data link starts at the same time of when the module is powered on
*4 When an external input device connected to X0 is on

(1) Module parameters in the data storage
(2) Read module parameters in the data storage and start the operation.

ON

(2)

ON

OFF

OFF

OFF

OFF

OFF

ON

(1)

Initial processing request flag (RWr0.b8)

Module power supply

*3

Channel 1 (CQ) external input signal 0

(RX0)

*4

Initial processing completion flag (RWw0.b8)

Remote READY (RWr0.b11)

Module setting

Controlled by the IO-Link module

«
...
141
142
143
144
145
...
»

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренд: Watts Страницы: 2

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Balboa Water Group Страницы: 28

Бренд: Hankscraft Runxin Страницы: 53

Бренд: 1Control Страницы: 8

Бренд: Manfrotto Страницы: 16

Бренд: Gardena Страницы: 16

Бренд: MADRIX Страницы: 28

Бренд: Game ready Страницы: 24

Бренд: Tenpilot Страницы: 2

Бренд: SMC Networks Страницы: 10

Бренд: McIntosh Страницы: 68

Бренд: u-blox Страницы: 157

Бренд: Airlow Страницы: 20

WFHC 06Z 02 HC RF 24

Бренд: Watts Страницы: 18

Бренд: Waters Страницы: 39

DHI-IPMECD-3021 Series

Бренд: Dahua Technology Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды