Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 106

Страница: 106 / 162

104

9 PROGRAMMING
9.2 Program Example of Setting Parameters Using a Dedicated Instruction

Click [OK] button on the following window to add a module label of the CC-Link IE Field Network master/local module.

Configure "Required Settings" of "Module Parameter" in the following way.

[Navigation window]



[Parameter]



[Module Information]



[RJ71GF11-T2]



[Module Parameter]



[Required

Settings]

Configure the network in the following way.

[Navigation window]



[Parameter]



[Module Information]



[RJ71GF11-T2]



[Module Parameter]



[Basic Settings]



[Network Configuration Settings]

Close the "CC IE Field Configuration" window.

[CC IE Field Configuration]



[Close with Reflecting the Setting]

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Результаты поиска

Содержание CC-Link IE Field NZ2GF12A-60IOLH8

Отзывы:

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренды по названию

Популярные бренды

Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8, Руководство пользователя

Результаты поиска

Содержание CC-Link IE Field NZ2GF12A-60IOLH8

Отзывы:

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренды по названию

Популярные бренды