Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 53

Страница: 53 / 162

6 Parameter Setting

6.3 Changing the IO-Link Module Parameters

6.3

Changing the IO-Link Module Parameters

This section describes the procedure for changing the parameter.
The precautions for changing the parameter are the same as those in the following section.



Page 46 Precautions

Setting via the engineering tool

Changing the network configuration

When changing the network configuration diverting the created project, set the parameter in the following procedure.

Power off the module.

Connect the modules again according to the desired network configuration.

Power on the module.

Open the "CC IE Field Configuration" window.

For the master/local module RJ71GF11-T2

[Navigation window]



[Parameter]



[Module Information]



[RJ71GF11-T2]



[Module Parameter]



[Basic Settings]



[Network Configuration Settings]

Drag and drop a module to set the IO-Link module. Input a numerical value to set the station number of the station.
Change the value as necessary.

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Результаты поиска

Содержание CC-Link IE Field NZ2GF12A-60IOLH8

Отзывы:

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренды по названию

Популярные бренды

Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8, Руководство пользователя

Результаты поиска

Содержание CC-Link IE Field NZ2GF12A-60IOLH8

Отзывы:

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренды по названию

Популярные бренды