Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 162

background image

30

4 SYSTEM CONFIGURATION
4.1 Applicable Systems

IO-Link cable

For details on IO-Link cables, refer to the following.



Page 31 Recommended Connectable Device List

Available software

The following software is available for settings and diagnostics of the IO-Link module. (



Manuals of each software)

When the latest software is required, please consult your local Mitsubishi representative.

Applicable profile

To use the parameter setting function of an IO-Link module, the profile is required.
The profile is a setting file that stores information required for the start-up, operation, and maintenance of devices supporting
the CC-Link family.
A module is added to "Module List" of "CC IE Field Configuration" window by profile registration to an engineering tool. For the
profile registration, refer to the operating manual for the engineering tool used.

Applicable devices

IO-Link devices and I/O devices incompatible with IO-Link can be connected in combination.
The IO-Link mode and SIO mode can be set separately on the channels of the IO-Link module.

■

IO-Link mode

If the channels are set in the IO-Link mode, a maximum of eight IO-Link devices can be connected.
IO-Link communication is performed via the CQ terminal of the IO-Link connector.

■

SIO mode (digital input, digital output)

If the channels are set in the SIO mode, a maximum of 16 signals are available. Each signal can be separately configured for
input/output.
Input/output is performed via the CQ and Q terminals of the IO-Link connector.
Both the input type and output type are negative common (source type).

• To change the operation mode, use the Channel n (CQ/Q) I/O switching command (RY10 to RY1F) and the

Channel n mode switching command (RY30 to RY37). (



Page 136 Channel n (CQ/Q) I/O switching

command (RY10 to RY1F), Page 137 Channel n mode switching command (RY30 to RY37))

• To use I/O devices not compatible with IO-Link, use the SIO mode.

Product name

Function and application

GX Works2

Software for system design, programming, debugging, and maintenance of the programmable controller.

GX Works3

MELSOFT Navigator

Integrated application of GX Works2 and GX Works3.

FDC

Application for DTM. Only IO-Link modules of which firmware version is 2.0.2 or later are supported.

M_CommDTM-IOLink

IODD DTM Configurator

«
...
30
31
32
33
34
...
»

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренд: VADDIO Страницы: 2

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Van Air Страницы: 4

Бренд: U.S. Divers Страницы: 22

Бренд: Casambi Страницы: 2

Бренд: Automated Logic Страницы: 10

Бренд: Jeckson Electric Страницы: 2

Бренд: VIPA Страницы: 394

SmartStuff Series

Бренд: TCP Страницы: 2

Бренд: Astrosyn Страницы: 7

SUNSAVER SS-10-12V

Бренд: Morningstar Страницы: 26

Бренд: NovaStar Страницы: 11

Бренд: Black Stone Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды