Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 162

background image

11 TROUBLESHOOTING

11.1 Checking the LEDs

119

11

When the RUN LED is off

When the DISPLAY1 LED or DISPLAY2 LED flashes in red

If link-up processing is repeated due to a condition of a device on the line, it may take a longer time for the
LINK LED to turn on. This phenomenon may be eliminated by changing the module PORT into which the
Ethernet cable is connected (example: P1



P2).

Check item

Action

Does the voltage of the module power supplied externally reach to the
voltage of the specifications?

Check that the module power supply voltage is within the range of performance
specifications. After the check, power off and on the module.

Does any hardware error occur?

If the RUN LED does not turn on even after the module power supply is turned off and
on, the possible cause is a module failure. Please consult your local Mitsubishi
representative.

Check item

Action



The possible cause is a module failure. Please consult your local Mitsubishi
representative.

«
...
119
120
121
122
123
...
»

Содержание CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CC-Link IE Field NZ2GF12A-60IOLH8

Бренд: Icom Страницы: 30

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ray Страницы: 11

Бренд: MAKOT Страницы: 6

Бренд: U-Prox Страницы: 3

Бренд: U-Prox Страницы: 2

Бренд: East Coast Datacom Страницы: 14

SUPERSTAR E-3000/F2

Бренд: praher Страницы: 10

Бренд: IDEC Страницы: 97

AQUASNAP 30RA "B"

Бренд: Carrier Страницы: 36

Бренд: ECKELMANN Страницы: 147

IntelliCross TouchFree Kit

Бренд: Novax Страницы: 3

Бренд: Daikin Страницы: 19

Бренд: Samcen Страницы: 65

Бренд: Dudley Страницы: 8

PLATINUM PS-9003

Бренд: HydroQuip Страницы: 24

Бренд: Znshine Solar Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды