manualshive.com logo in svg

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lenovo System x3650 M4 HD Скачать руководство пользователя страница 973

•

I.580A6 [I.580A6] Memory spare copy has completed successfully.

Explanation:

Spare Copy Complete

Severity

Info

User Response

Complete the following steps:

1. Check system log for related DIMM failures and replace those DIMMs.

•

S.1100B [S.1100B] CATERR(IERR) has asserted on processor %.

Explanation:

Processor CATERR(IERR) has asserted

Severity

Error

User Response

Complete the following steps:

1. Check IBM support site for an applicable service bulletin or firmware update that applies to

this Processor error.

2. (Trained Service technician only) Replace the Processor.

•

S.1100C [S.1100C] An uncorrectable error has been detected on processor %.

Explanation:

Uncorrectable processor error detected

Severity

Error

User Response

Complete the following steps:

1. Check IBM support site for an applicable service bulletin or firmware update that applies to

this error.

2. Reboot system. If problem persists escalate to the next level of supprt.

•

S.2011001 [S.2011001] An Uncorrected PCIe Error has Occurred at Bus % Device % Function %.

The Vendor ID for the device is % and the Device ID is %.

Explanation:

PCI SERR Detected

Severity

Error

User Response

Complete the following steps:

1. If this node and/or any attached cables were recently installed, moved, serviced or upgraded, a.

Reseat Adapter and any attached cables. b. Reload Device Driver c. If device is not recognized,
reconfiguring slot to Gen1 or Gen2 may be required. Gen1/Gen2 settings can be configured

Appendix B. UEFI/POST diagnostic codes

961

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды