Lenovo System x3650 M4 HD Скачать руководство пользователя страница 247

Страница: 247 / 1168

Connector

Rentention pins

ServeRAID memory module

Figure 159. ServeRAID adapter memory module installation

Step 6.

Connect the other end of the cable to the flash power module.

00000

Flash power module cable

ServeRAID memory module

Flash power module

Figure 160. Cable installation

Note:

Make sure the flash power module is seated properly (see “Replacing a RAID adapter

battery or flash power module” on page 203).

Step 7.

Reconnect the power cords and any cables that you removed.

Step 8.

Reinstall the cover (see “Replacing the cover” on page 196).

Step 9.

Slide the server into the rack.

Step 10. Turn on the peripheral devices and the server.

Removing the dual-port network adapter

Use this information to remove the dual-port network adapter.

Chapter 6

Removing and replacing components

235

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды