Lenovo System x3650 M4 HD Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 1168

Lenovo System x3650 M4 HD Скачать руководство пользователя страница 143

System error
LED

Locator LED

Power LED

Dual-por t network
adapter LED

IMM hear tbeat
LED

RTMM hear tbeat LED

Standby power
LED

System battery
error LED

Fan 4
error LED

Fan 3
error LED

Microprocessor 2
error LED

Fan 2
error LED

Fan 1
error LED

Microprocessor 1
error LED

System board
error LED

DIMM 19-24
error LEDs
(under the latches)

DIMM 1-6
error LEDs
(under the latches)

DIMM 7-18
error LEDs
(under the latches)

Figure 94. System board error LEDs

Power-supply LEDs

The following minimum configuration is required for the server to start.
• One microprocessor in microprocessor socket 1
• One 2 GB DIMM on the system board
• One power supply
• Power cord
• Four cooling fans
• One PCI riser-card assembly in PCI connector 1

AC power-supply LEDs

Use this information to view AC power-supply LEDs.

The following minimum configuration is required for the DC LED on the power supply to be lit:
• Power supply
• Power cord

Note:

You must turn on the server for the DC LED on the power supply to be lit.

The following illustration shows the locations of the power-supply LEDs on the ac power supply.

Troubleshooting

131

«
...
141
142
143
144
145
...
»

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды