Lenovo System x3650 M4 HD Скачать руководство пользователя страница 297 | Manualshive

Страница: 297 / 1168

Lenovo System x3650 M4 HD Скачать руководство пользователя страница 297

Step 8.

Remove the microprocessor from the socket.

a.

Select the empty installation tool and ensure that the handle is in the open position. If the
installation tool handle is not in the open position, use the following instructions for your
installation tool:

• If using Installation Tool A, twist the microprocessor installation tool handle counterclockwise

to the open position.

Handle

Installation tool

Figure 211. Installation tool handle adjustment

• If using Installation Tool B,

1

lift the interlock latch and hold it up while you

2

twist the

microprocessor installation tool handle counterclockwise to the open position, and then
release the interlock latch. The following illustration of the installation tool shows the
location of the interlock latch and counterclockwise rotation of the handle before loading
the microprocessor.

H

Figure 212. Installation tool handle adjustment

b.

Align the installation tool with the screws, as shown in the following graphic, and lower the
installation tool on the microprocessor. The installation tool rests flush on the socket only
when it is aligned correctly.

Removing and replacing components

285

«
...
295
296
297
298
299
...
»

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды