Lenovo System x3650 M4 HD Скачать руководство пользователя страница 280

Страница: 280 / 1168

Battery

Figure 188. System battery removal

If there is a rubber cover on the battery holder, use your fingers to lift the battery cover from
the battery connector.

Use one finger to tilt the battery horizontally out of its socket, pushing it away from the socket.

Attention:

Neither tilt nor push the battery by using excessive force.

Figure 189. System battery removal

Use your thumb and index finger to lift the battery from the socket.

Attention:

Do not lift the battery by using excessive force. Failing to remove the battery

properly may damage the socket on the system board. Any damage to the socket may require
replacing the system board.

Step 6.

Dispose of the battery as required by local ordinances or regulations. See the

Lenovo Environmental

Notices and User's Guide

on the Lenovo

Documentation

CD for more information.

268

Lenovo System x3650 M4 HD Installation and Service Guide

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды