Lenovo System x3650 M4 HD Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 1168

Lenovo System x3650 M4 HD Скачать руководство пользователя страница 30

Hard disk drive
activity LED (green)

Hard disk drive
status LED (yellow)

Rack
release
latch

Operator
information panel

Rack
release
latch

2.5-inch hard disk drive bays

Video and USB
breakout connector

Tag

Figure 6. Front view: 2.5-inch hard-disk-drive bay model

00000

00000

00000

00000

00000

00000

00000

00000

Hard disk drive
activity LED (green)

Hard disk drive
status LED (yellow)

Rack
release
latch

Operator
information panel

Rack
release
latch

2.5-inch hard disk
drive bays

Video and USB
breakout connector

1.8-inch solid state
drive bays

0000

0000

0000

Hard disk drive
activity LED (green)

Hard disk drive
status LED (yellow)

Figure 7. Front view: 2.5-inch hard-disk-drive bay and 1.8-inch solid-state-drive bay model

•

Rack release latches

: Press the latches on each front side of the server to remove the server from the

rack.

•

Hard disk drive activity LEDs

: This LED is used on hot-swap hard disk drives. Each hot-swap hard disk

drive has an activity LED, and when this LED is flashing, it indicates that the drive is in use.

•

Hard disk drive status LEDs

: This LED is used on hot-swap hard disk drives. When this LED is lit, it

indicates that the drive has failed. If an optional ServeRAID controller is installed in the server, when this
LED is flashing slowly (one flash per second), it indicates that the drive is being rebuilt. When the LED is
flashing rapidly (three flashes per second), it indicates that the controller is identifying the drive.

•

Operator information panel

: This panel contains controls and LEDs that provide information about the

status of the server. For information about the controls and LEDs on the operator information panel, see
“Operator information panel” on page 19.

•

Tag

: Pull the tag forward to access the tag.

•

Video and USB breakout connector

: Connect the video and USB breakout cable to this connector (see

“Video and USB breakout cable” on page 19 for more information).

•

Video connector

(optional): Connect a monitor to this connector. The video connectors on the front and

rear of the server can be used simultaneously.

Note:

The maximum video resolution is 1600 x 1200 at 75 Hz.

18

Lenovo System x3650 M4 HD Installation and Service Guide

«
...
28
29
30
31
32
...
»

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды