Lenovo System x3650 M4 HD Скачать руководство пользователя страница 1027

Страница: 1027 / 1168

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-903-000 : IANet:Interrupts Test Failed

A failure was detected during the Interrupt test.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. Check interrupt assignments in the PCI Hardware section of the DSA Diagnostic Log. If the

ethernet device is sharing interrupts, if possible modify the interrupt assignments using F1
Setup to assign a unique interrupt to the device.

4. Rerun the test.

5. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-904-000 : IANet:Loopback Test Failed

A failure was detected during the Loopback test.

Recoverable

Severity

Error

Serviceable

Appendix C. DSA diagnostic test results

1015

«
...
1025
1026
1027
1028
1029
...
»

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды