Lenovo System x3650 M4 HD Скачать руководство пользователя страница 209

Страница: 209 / 1168

000000000000

Cover-release
latch

Figure 118. Cover installation

Step 6.

Slide the server all the way into the rack until it latches.

Step 7.

Reconnect the external cables and power cords.

Removing the bezel

Use this information to remove the bezel.

To remove the bezel, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Remove all the cables that are connected to the front of the server.

Step 3.

Remove the screws from the bezel.

Note:

Use the hex screw driver to remove the screws.

Chapter 6

Removing and replacing components

197

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды