Lenovo System x3650 M4 HD Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 1168

Lenovo System x3650 M4 HD Скачать руководство пользователя страница 173

If possible, have this information available when requesting assistance from Lenovo.

The model name and serial number are located on the ID label on the front of the server as shown in
the following illustration.

Note:

The illustrations in this document might differ slightly from your hardware.

ID label

Figure 98. ID label

• Machine type and model

• Microprocessor or hard disk drive upgrades

• Failure symptom

– Does the server fail the diagnostic tests?

– What occurs? When? Where?

– Does the failure occur on a single server or on multiple servers?

– Is the failure repeatable?

– Has this configuration ever worked?

– What changes, if any, were made before the configuration failed?

– Is this the original reported failure?

• Diagnostic program type and version level

• Hardware configuration (print screen of the system summary)

• UEFI firmware level

• IMM firmware level

• Operating system software

You can solve some problems by comparing the configuration and software setups between working and
nonworking servers. When you compare servers to each other for diagnostic purposes, consider them
identical only if all the following factors are exactly the same in all the servers:

• Machine type and model

• UEFI firmware level

• IMM firmware level

• Adapters and attachments, in the same locations

• Address jumpers, terminators, and cabling

• Software versions and levels

Troubleshooting

161

«
...
171
172
173
174
175
...
»

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды