Lenovo System x3650 M4 HD Скачать руководство пользователя страница 316 | Manualshive

Страница: 316 / 1168

Lenovo System x3650 M4 HD Скачать руководство пользователя страница 316

Automatically contact Service

If this field is set to

Yes

, and you have enabled Electronic Service Agent (ESA), IBM Support will be

notified automatically if the event is generated.

While you wait for IBM Support to call, you can perform the recommended actions for the event.

User response

The actions that you should perform to solve the event.

Perform the steps listed in this section in the order shown until the problem is solved. After you perform
all of the actions that are described in this field, if you cannot solve the problem, contact IBM Support.

Note:

This list includes error codes and messages that might not apply to this machine type and model.

The following list shows the IMM2 error messages and suggested actions to correct the detected server
problems. For more information about IMM2, see the

Integrated Management Module II User's Guide

at http://publib.boulder.ibm.com/infocenter/ systemx/documentation/topic/ com.lenovo.sysx.imm2.doc/
printable_doc.html.

IMM Events that automatically notify Support

You can configure the IBM Flex System Manager or the CMM to automatically notify Support (also known as

call home

) if certain types of errors are encountered. If you have configured this function, see the table for

a list of events that automatically notify Support.

Table 25. Events that automatically notify Support

Event ID

Message String

Automatically
Notify Support

40000086-00000000

Test Call Home Generated by user [arg1].

Yes

40000087-00000000

Manual Call Home by user [arg1]: [arg2].

Yes

80010202-0701ffff

Numeric sensor [NumericSensorElementName] going low
(lower critical) has asserted.

Yes

80010902-0701ffff

Numeric sensor [NumericSensorElementName] going
high (upper critical) has asserted.

Yes

806f0021-2201ffff

Fault in slot [PhysicalConnectorSystemElementName] on
system [ComputerSystemElementName]. (No Op ROM
Space)

Yes

806f0021-2582ffff

Fault in slot [PhysicalConnectorSystemElementName] on
system [ComputerSystemElementName]. (All PCI Error)

Yes

806f0021-2c01ffff

Fault in slot [PhysicalConnectorSystemElementName] on
system [ComputerSystemElementName]. (Mezz Error)

Yes

806f0021-3001ffff

Fault in slot [PhysicalConnectorSystemElementName] on
system [ComputerSystemElementName]. (PCI 1)

Yes

806f0108-0a01ffff

[PowerSupplyElementName] has Failed. (Power Supply 1)

Yes

806f0108-0a02ffff

[PowerSupplyElementName] has Failed. (Power Supply 2)

Yes

806f010c-2001ffff

Uncorrectable error detected for
[PhysicalMemoryElementName] on Subsystem
[MemoryElementName]. (DIMM 1)

Yes

806f010c-2002ffff

Uncorrectable error detected for
[PhysicalMemoryElementName] on Subsystem
[MemoryElementName]. (DIMM 2)

Yes

304

Lenovo System x3650 M4 HD Installation and Service Guide

«
...
314
315
316
317
318
...
»

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды