Lenovo System x3650 M4 HD Скачать руководство пользователя страница 292

Страница: 292 / 1168

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 3.

Remove the cover (see “Removing the cover” on page 195).

Step 4.

Remove the bezel (see “Removing the bezel” on page 197).

Step 5.

Align the assembly on the bezel and install the two screws.

Note:

Use the hex screw driver to install the two screws.

Hex screw driver

Operator information
panel assembly

Screws

Figure 204. Operator information panel installation

Step 6.

Replace the bezel (see “Replacing the bezel” on page 198).

Step 7.

Connect the operator information cable from the system board to the rear of the assembly (see
“Cabling operator information panel” on page 180).

Operator information
panel cable

Operator information
panel assembly

Figure 205. Operator information panel cable installation

Step 8.

Replace the cover (see “Replacing the cover” on page 196).

Step 9.

Slide the server into the rack.

Step 10. Reconnect the power cords and any cables that you removed.

Step 11. Turn on the peripheral devices and the server.

280

Lenovo System x3650 M4 HD Installation and Service Guide

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды