Lenovo System x3650 M4 HD Скачать руководство пользователя страница 516

Страница: 516 / 1168

2. Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling

the drive) b. Cable from the system board to the backplane

3. Replace the following components one at a time, in the order shown, restarting the server

each time: a. Hard disk drive b. Cable from the system board to the backplane c. Hard disk
drive backplane (n = hard disk drive number)

•

806f010d-041cffff : The Drive [StorageVolumeElementName] has been disabled due to a detected

fault. (Drive 28)

This message is for the use case when an implementation has detected a Drive was Disabled due to fault.

May also be shown as 806f010d041cffff or 0x806f010d041cffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0164

User Response

1. Run the hard disk drive diagnostic test on drive n.

2. Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling

the drive) b. Cable from the system board to the backplane

3. Replace the following components one at a time, in the order shown, restarting the server

each time: a. Hard disk drive b. Cable from the system board to the backplane c. Hard disk
drive backplane (n = hard disk drive number)

•

806f010d-041dffff : The Drive [StorageVolumeElementName] has been disabled due to a detected

fault. (Drive 29)

This message is for the use case when an implementation has detected a Drive was Disabled due to fault.

May also be shown as 806f010d041dffff or 0x806f010d041dffff

Severity

Error

Serviceable

Yes

504

Lenovo System x3650 M4 HD Installation and Service Guide

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3650 M4 HD

Отзывы:

Бренды по названию

Популярные бренды