manualshive.com logo in svg

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lenovo System x3650 M4 HD Скачать руководство пользователя страница 582

•

806f040c-2014ffff : [PhysicalMemoryElementName] Disabled on Subsystem

[MemoryElementName]. (DIMM 20)

This message is for the use case when an implementation has detected that Memory has been Disabled.

May also be shown as 806f040c2014ffff or 0x806f040c2014ffff

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0131

User Response

1. Make sure the DIMM is installed correctly.

2. If the DIMM was disabled because of a memory fault (memory uncorrectable error or memory

logging limit reached), follow the suggested actions for that error event and restart the server.

3. Install the DIMM to another slot and restart the server.

4. Check the IBM support website for an applicable retain tip or firmware update that applies to

this memory event. If no memory fault is recorded in the logs and no DIMM connector error LED
is lit, you can re-enable the DIMM through the Setup utility or the Advanced Settings Utility (ASU).

•

806f040c-2015ffff : [PhysicalMemoryElementName] Disabled on Subsystem

[MemoryElementName]. (DIMM 21)

This message is for the use case when an implementation has detected that Memory has been Disabled.

May also be shown as 806f040c2015ffff or 0x806f040c2015ffff

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

System - Other

570

Lenovo System x3650 M4 HD Installation and Service Guide

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды