Kval Commander III страница 106 Скачать руководство пользователя

Страница: 106 / 168

About the Tool Config Tabs

3-25

Commander III Operation Manual

About the Tool Config Tabs

This section includes descriptions of the

Tool Config

Screen

The

Tool Config Screen

contains:

• Access to Hinge tools and Lock tools

• Pop-up menus to enter information about each tool (Specifications, Router or Drill)

• The ability to enable or disable specific tool slots

• The ability to name the tools to familiar names.

• The ability to lock and unlock the ability to enter data.

To display the

Configuration Screen

, select the

Tool Config

tab and choose

Hinge Tool

s or

Lock

Tools.

At this screen specifications of the tool is entered and saved to the database. This information is
valuable to compute and provide the most precise cut available.

List of Tools
Available

Pop-Up Menus: enter
tool data.(Router,Drill
and Chisels (opt)

Содержание Commander III









































































































































































Результаты поиска

Содержание Commander III

Отзывы:

Похожие инструкции для Commander III

Бренды по названию

Популярные бренды

Kval Commander III, Руководство по эксплуатации

Результаты поиска

Содержание Commander III

Отзывы:

Похожие инструкции для Commander III

Бренды по названию

Популярные бренды