Kval Commander III страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 168

background image

Safety Sign-Off Sheet

KVAL Commander III Operation Manual

1-20

Safety Sign-Off Sheet

Machine Model Number:_____________________________

A Note to the Operator:

This machine can help you be highly productive only if you understand how to use it properly and
follow the safe operating practices described in this document and the machine’s manual. If you
do not understand the machine’s proper operation or ignore the safe operating practices, this
machine can hurt or kill you. It’s in your best interest to safely and properly operate this machine.

Personnel Safety Concerns:

• I have been properly trained in the operation of this machine.

• I will always wear ear protection when operating this machine.

• I will always wear eye protection when operating this machine.

• I will never wear loose clothing or gloves when operating this machine.

• I will watch out for other people. Make sure everyone is clear of this machine

before operation.

• I will always follow my company’s safety procedures. I have read and understand

these guidelines.

Machine Safety Concerns:

• I have been given a tour of the machine and understand all the safety labels, E-

Stops and the actions to take in case of an emergency.

• I will make sure all guards are in place before operation

• I will turn off the compressed air, before loading hardware (staples, screws, etc)

• I will turn off the electrical power, for setup

• If the machine should operate in an unexpected manner stop production I will

immediately and notify a manager, a supervisor, or a qualified service technician.

I have read and understand this document and agree to operate this machine in a safe man-
ner as described above.

Employee

Name (print):

___________________

Signature:

__________________

Date:

____/____/____

Supervisor/Safety Officer/Trainer

Name (print):

__________________

Signature:

__________________

Date:

____/____/___

Note:

It is recommended you make a copy of this sheet for new operators. If a copy is

needed, you may download a PDF at the KVAL website (

http://www.kvalinc.com

).

You may also contact our Service Department at (800) 553-5825 or email at
[email protected].

«
...
28
29
30
31
32
...
»

Содержание Commander III









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Commander III

Бренд: Dairyland Страницы: 21

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

Бренд: YMC Страницы: 49

Бренд: Octane Fitness Страницы: 8

Бренд: Octane Fitness Страницы: 10

Бренд: OCENCO Страницы: 48

Бренд: Ocean Optics Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды