Kval Commander III Скачать руководство пользователя страница 39

Страница: 39 / 168

Controls at the Library Screen

2-9

KVAL Manual

Using the Door File Table

The list below shows information about general use of the tables. See the figure below.

• Each library table shows the files in the selected database.

• Click the desired Table Heading to sort by Name, Description, Date Created or

Dated Modified.

• At the top enter key words to search by name or description.

• Select the Display Deleted Check Box to view or recover deleted door files.

Tip:

Change the column widths by selecting the column border and dragging to the
desired width.

Using the Display Deleted Check Box (Recover a Door File)

Follow this procedure to recover a door file.

Select the

Display Deleted Check Box

, located in the upper right hand corner.

Deleted files are highlighted in red.

Select the file to be recovered.

At the bottom of the page, select the

Restore Button

to recover the file.

Содержание Commander III









































































































































































Результаты поиска

Содержание Commander III

Отзывы:

Похожие инструкции для Commander III

Бренды по названию

Популярные бренды

Kval Commander III, Руководство по эксплуатации

Результаты поиска

Содержание Commander III

Отзывы:

Похожие инструкции для Commander III

Бренды по названию

Популярные бренды