manualshive.com logo in svg

Kval Commander III, Руководство по эксплуатации

Kval Commander III - мощный инструмент для управления процессами. Загрузите бесплатное руководство по обслуживанию с нашего сайта. Получите доступ к подробной информации о настройке и технической поддержке для оптимальной производительности. Скачайте руководство с manualshive.com.

Поделиться
Скачать
background image

KVAL Commander III Operation Manual

NOTICE OF OWNERSHIP OF KvalCAM SOFTWARE AND LIMITED LICENSE TO 
USE

READ THIS NOTICE CAREFULLY BEFORE USING THE KvalCAM SOFTWARE WHICH OPERATES KVAL 
MACHINERY. THIS DOCUMENT CONSTITUTES NOTICE TO YOU THAT YOU HAVE A LIMITED 
LICENSE TO USE THE KvalCAM SOFTWARE ON THE TERMS AND CONDITIONS APPEARING BELOW. 

BY USING THE KvalCAM SOFTWARE YOU ARE CONSENTING TO BE BOUND BY THIS LIMITED 
LICENSE. IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS LICENSE, THEN DO NOT USE THE 
KvalCAM SOFTWARE.

KVAL, Inc., is the owner of all rights in respect of the software and documentation (referred to as “Licensor”). You 
are the purchaser of KVAL Machinery operated by the KvalCAM Software are the “Licensee”. 

The computer program(s) and related documentation and materials (herein collectively referred to as “the KvalCAM 
Software” and further defined herein) which are used in the operation of the KVAL Machinery are licensed, not sold, 
to you for use only upon the limited terms of this license, and Licensor reserves any rights not expressly granted to 
you.   Licensor retains all ownership of the KvalCAM Software. 

Title, ownership rights, and intellectual property rights in the KvalCAM Software shall remain with KVAL, Inc. The 
KvalCAM Software is protected by copyright laws and treaties. Title and related rights in the content generated 
through the KvalCAM Software are also the property of the Licensor and are protected by applicable law.

1.

Definitions

. 

a.

“KvalCAM Software” means the KvalCAM computer application installed in the KVAL 

Machinery and written documentation and materials provided to you, as well as any revisions or 
updates of such computer application and documentation.

b.

“Install” means storing of the KvalCAM Software in the computer component of the KVAL 

Machinery.

c.

“Use” means executing the KvalCAM Software for purpose of operating the KVAL Machin-

ery and use of the documentation for properly operating KvalCAM Software.

2.

Grant of License

. 

a.

Licensor hereby grants Licensee a non-exclusive, non-transferable license to Use the Kval-

CAM Software upon payment of all amounts due for the purchase of the related KVAL Machin-
ery. 

b.

Licensee will make no copies of the KvalCAM Software or alter the KvalCAM Software in 

any way. Title to the KvalCAM Software will remain vested in Licensor, and nothing in this 
License will give or convey any right, title or interest therein to Licensee except as a licensee.

c.

Licensee agrees that it will use the KvalCAM Software or related documentation directly or 

indirectly for the benefit of Licensee, and only pursuant to the scope of the grant of the License 
set forth herein.

d.

Licensee will not decode, alter, decompile, reverse engineer, perform reverse analysis on or 

disassemble the KvalCAM Software.

e.

This License will terminate automatically if Licensee fails to comply with the limitations 

described above.

Содержание Commander III









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Commander III

UnionSpecial 2200 Series Instructions, Engineer'S And Illustrated Parts Manual preview
2200 Series
Бренд: UnionSpecial Страницы: 56
Taylor Made 12008 Instructions preview
12008
Бренд: Taylor Made Страницы: 2
York Fitness 1003 Assembly Instruction Manual preview
1003
Бренд: York Fitness Страницы: 18
Safco 1005 Instructions preview
1005
Бренд: Safco Страницы: 2
Omni 4000 Series Operation & Maintenance Manual preview
4000 Series
Бренд: Omni Страницы: 193
Garelick 19250 Installation Instructions preview
19250
Бренд: Garelick Страницы: 2
Garelick 74002 Assembly And Installation Instructions preview
74002
Бренд: Garelick Страницы: 2
Labelmate UCAT-S User Manual preview
UCAT-S
Бренд: Labelmate Страницы: 61
Labconco FreeZone Plus User Manual preview
FreeZone Plus
Бренд: Labconco Страницы: 62
NARGESA PC16 Instruction Book preview
PC16
Бренд: NARGESA Страницы: 37
NARGESA NOA60 Technical Features preview
NOA60
Бренд: NARGESA Страницы: 6
Quark-Elec QK-A031 Setup Manual preview
QK-A031
Бренд: Quark-Elec Страницы: 2
Yamaha MagicStomp Effect List preview
MagicStomp
Бренд: Yamaha Страницы: 31
JBL 54368 Instruction Manual preview
54368
Бренд: JBL Страницы: 17
olympia electronics GR-460/WP Quick Start Manual preview
GR-460/WP
Бренд: olympia electronics Страницы: 2
Lutron Electronics VIMCO Sivoia SV-CCI-GRP Operating Instructions preview
VIMCO Sivoia SV-CCI-GRP
Бренд: Lutron Electronics Страницы: 2
SprotDog Pro hunter 2525 Operating Manual preview
Pro hunter 2525
Бренд: SprotDog Страницы: 28
Parkside PALA 2000 A1 Operation And Safety Notes preview
PALA 2000 A1
Бренд: Parkside Страницы: 88

Бренды по названию

Популярные бренды

Загрузить еще бренды