Kval Commander III страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 168

background image

Safety First!

KVAL Commander III Operation Manual

1-6

Safety First!

This machine is a powerful electro-mechanical motion control
system. You should test your motion system for safety under
all potential conditions.

Failure to do so can result in dam-

age to equipment and/or serious injury to personnel.

Safety Sheet Sign-Off Sheet

At the end of this chapter, there is a safety sign-off sheet. It lists personnel and machine safety cri-
teria to understand before operating the machine. It is highly recommended that personnel operat-
ing, working on a machine meet the criteria listed in this sheet. It is recommended the sheet be
signed and kept for records. See “Safety Sign-Off Sheet” on page 1-20.

Safety Terminology of Labels

In addition to the nameplate, KVAL machines may have other warning labels or decals that pro-
vide safety information to operators. Safety labels should be clearly visible to the operator and
must be replaced if missing, damaged, or illegible.

There are three types of warning labels or decals:

•

DANGER

means if the danger is not avoided, it will cause death or serious injury.

•

WARNING

means if the warning is not heeded, it can cause death or serious

injury.

•

CAUTION

means if the precaution is not taken, it may cause minor or moderate

injury.

Safety Guidelines

In addition to the caution and warning labels affixed to this machine, follow the guidelines below
to help ensure the safety of equipment and personnel.

Ensure that all employees who operate this machine
are aware of and adhere to all safety precautions
posted on the machine and are trained to operate this
machine in a safe manner.

Training

«
...
14
15
16
17
18
...
»

Содержание Commander III









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Commander III

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: XM Fitness Страницы: 10

Бренд: S&C Страницы: 27

Бренд: S&C Страницы: 56

IntelliRupter PulseCloser

Бренд: S&C Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды