Kval Commander III Скачать руководство пользователя страница 107

Страница: 107 / 168

About the Tool Config Tabs

3-26

Commander III Operation Manual

Unlock the Tool Slot Configuration

Note:

The ability to lock and unlock

Tool Configure Menu

is a configurable option. At

customer request this option can be turned on or off.

The configuration screens are passwords protected. To unlock the screens, select the Unlock but-
ton and enter the password in the password popup menu.

About Using Tool Configuration

To Unlock

Select the

Unlock Button.

Enter Password in the Pop-Up window.

Click

OK.

The

Unlock Button

will change to a

Lock But-

ton.

Tools can now be configured.

To Lock

Select the

Lock Button

and repeat instruction above.

Identify the tool that needs replacement.Measure
the dimensions and capture the data. (Use this
information to populate the

Drill or Router

pop-

up screens).

Select the

Tool Slot

Enter the data into the pop-up screen.

Содержание Commander III









































































































































































Результаты поиска

Содержание Commander III

Отзывы:

Похожие инструкции для Commander III

Бренды по названию

Популярные бренды

Kval Commander III, Руководство по эксплуатации

Результаты поиска

Содержание Commander III

Отзывы:

Похожие инструкции для Commander III

Бренды по названию

Популярные бренды