KTM 2011 690 SMC AUS Скачать руководство пользователя

Страница: 75 / 229

WHEELS

12.7.2

Installing the rear wheel

Warning

Danger of accidents

Reduced braking efficiency due to oil or grease on the brake discs.

–

Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Warning

Danger of accidents

No braking effect when operating the rear brake.

–

After installing the rear wheel, always operate the foot brake until the pressure point is reached.

Main work

–

Check the rear hub rubber dampers. (

p. 77)

600628-10

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Replace the wheel bearing.

–

Remove the bushing

. Clean and grease the roll surfaces of the bushing and the

shaft seal ring

Long-life grease (

p. 208)

–

Clean and grease the thread of the wheel spindle and nut

Long-life grease (

p. 208)

–

Install the rubber damper and rear sprocket carrier in the rear wheel.

–

Position the rear wheel.

The brake linings are correctly positioned.

100270-10

–

Push the rear wheel forward as far as possible and lay the chain on the rear
sprocket.

–

Mount the wheel spindle, chain adjusters and nuts.
Guideline

In order that the rear wheel is correctly aligned, the markings on the left and
right chain adjusters must be in the same position relative to the reference
marks

Info

Mount the left and right chain adjusters

in the same position.

–

Tighten nut

Guideline

Nut, rear wheel spindle

M25x1.5

90 Nm
(66.4 lbf ft)

–

Operate the foot brake lever repeatedly until the brake linings are in contact with
the brake disc and there is a pressure point.

Finishing work

–

Take the motorcycle off of the rear wheel stand. (

p. 10)

12.7.3

Removing the brake disc of the rear brake

Preparatory work

–

Raise the motorcycle with the rear wheel stand. (

p. 10)

–

Remove the rear wheel. (

p. 72)

306860-10

Main work

–

Remove screws

. Take off the brake disc.

Содержание 2011 690 SMC AUS






































































































































































































































Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды

KTM 2011 690 SMC AUS, Руководство по ремонту

Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды