manualshive.com logo in svg

KTM 2011 690 SMC AUS, Руководство по ремонту

"KTM 2011 690 SMC AUS Repair Manual - бесплатное руководство по ремонту для мотоцикла KTM 690 SMC AUS 2011 года. Загрузите его с нашего сайта, чтобы получить подробные инструкции по обслуживанию и ремонту вашего мотоцикла. Доступно для скачивания на manualshive.com."

Поделиться
Скачать
background image

18

WATER PUMP, COOLING SYSTEM

163

» If the coolant level does not meet specifications:

–

Correct the coolant level and find out the cause of the loss.

Alternative 1

Coolant (

p. 206)

Alternative 2

Coolant (mixed ready to use) (

p. 206)

–

Mount the radiator cap.

18.4

Checking the coolant level

Warning

Danger of scalding

 

During motorcycle operation, the coolant gets very hot and is under pressure.

–

Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the
engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.

Warning

Danger of poisoning

 

Coolant is poisonous and a health hazard.

–

Coolant must not come into contact with the skin, eyes, or clothing. If contact occurs with the eyes, rinse with water imme-
diately and contact a physician. Immediately clean contaminated areas on the skin with soap and water. If coolant is swal-
lowed, contact a physician immediately. Change clothing that is contaminated with coolant. Keep coolant out of reach of
children.

Condition

Engine is cold.

B01293-10

–

Stand the motorcycle on its side stand on a horizontal surface.

–

Check the coolant level in the compensating tank

1

.

The coolant level must be within the range shown in the figure.

» If the coolant level does not meet specifications:

–

Correct the coolant level.

Alternative 1

Coolant (

p. 206)

Alternative 2

Coolant (mixed ready to use) (

p. 206)

100284-10

–

Screw off the radiator cap

2

and check the coolant level in the radiator.

The radiator must be completely filled.

» If the coolant level does not meet specifications:

–

Correct the coolant level and find out the cause of the loss.

Alternative 1

Coolant (

p. 206)

Alternative 2

Coolant (mixed ready to use) (

p. 206)

–

Mount the radiator cap.

Содержание 2011 690 SMC AUS






































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 690 SMC AUS

Yamaha MT01X Owner'S Manual preview
MT01X
Бренд: Yamaha Страницы: 92
Yamaha TTR90(M) Owner'S Service Manual preview
TTR90(M)
Бренд: Yamaha Страницы: 287
Yamaha YZ125(V) Owner'S Service Manual preview
YZ125(V)
Бренд: Yamaha Страницы: 572
Yamaha YZ250(P)/LC Owner'S Service Manual preview
YZ250(P)/LC
Бренд: Yamaha Страницы: 584
Yamaha YZ 2017 Series Owner'S Service Manual preview
YZ 2017 Series
Бренд: Yamaha Страницы: 410
Yamaha YZ125(W)/W1 Owner'S Service Manual preview
YZ125(W)/W1
Бренд: Yamaha Страницы: 576
Yamaha YZ250F(T) Owner'S Service Manual preview
YZ250F(T)
Бренд: Yamaha Страницы: 668
Yamaha YZ250(V) Owner'S Service Manual preview
YZ250(V)
Бренд: Yamaha Страницы: 596
Yamaha YZ250F(N)/LC Owner'S Service Manual preview
YZ250F(N)/LC
Бренд: Yamaha Страницы: 656
Yamaha YZ 2023 Series Owner'S Service Manual preview
YZ 2023 Series
Бренд: Yamaha Страницы: 378
Suzuki RV50 Service Manual preview
RV50
Бренд: Suzuki Страницы: 59
hepco & becker Easyrack 6622520 01 01 Mounting Instructions preview
Easyrack 6622520 01 01
Бренд: hepco & becker Страницы: 4
LAZER Lugano User Manual preview
Lugano
Бренд: LAZER Страницы: 19
Kong MOUSE WORK Manual preview
MOUSE WORK
Бренд: Kong Страницы: 72
KTM Power Parts 60005099300 Information preview
60005099300
Бренд: KTM Power Parts Страницы: 12
Yamaha YZ85Y Owner'S Manual preview
YZ85Y
Бренд: Yamaha Страницы: 80
Yamaha YZF R1 2021 Owner'S Manual preview
YZF R1 2021
Бренд: Yamaha Страницы: 144
Yamaha YZ85M 2021 Owner'S Manual preview
YZ85M 2021
Бренд: Yamaha Страницы: 84

Бренды по названию

Популярные бренды

Загрузить еще бренды