KTM 2011 690 SMC AUS Скачать руководство пользователя | Manualshive

Страница: 17 / 229

background image

6

FORK, TRIPLE CLAMP

15

6.4

Cleaning the dust boots of the fork legs

Preparatory work

–

Jack up the motorcycle and secure it against falling over.

The front wheel is no longer in contact with the ground and the fork legs are no
longer under tension.

–

Remove the fork protector. (

p. 15)

L00350-10

Main work

–

Push dust boot

1

of both fork legs downwards.

Info

The dust boots should remove dust and coarse dirt particles from the fork
tubes. Over time, dirt can penetrate behind the dust boots. If this dirt is not
removed, the oil seals behind can start to leak.

Warning

Danger of accidents

Reduced braking efficiency due to oil or grease on the

brake discs.

–

Always keep the brake discs free of oil and grease, and clean them with
brake cleaner when necessary.

–

Clean and oil the dust boots and inner fork tube of both fork legs.

Universal oil spray (

p. 209)

–

Press the dust boots back into their normal position.

–

Remove excess oil.

Finishing work

–

Install the fork protector. (

p. 15)

–

Remove the motorcycle from the lift stand. (

p. 11)

6.5

Removing the fork protector

600633-11

–

Remove screws

1

and take off clamp.

–

Remove screws

2

on left fork leg. Remove the fork protector.

–

Remove the screws on the right fork leg. Remove the fork protector.

6.6

Installing the fork protector

600633-10

–

Position the fork protection on the left fork leg. Mount and tighten screws

1

.

Guideline

Remaining screws, chassis

M6

10 Nm (7.4 lbf ft)

–

Position the brake line and cable harness. Put the clamp on, mount and tighten
screws

2

.

–

Position the fork protection on the right fork leg. Mount and tighten the screws.
Guideline

Remaining screws, chassis

M6

10 Nm (7.4 lbf ft)

«
...
15
16
17
18
19
...
»

Содержание 2011 690 SMC AUS






































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 690 SMC AUS

Бренд: Baja motorsports Страницы: 20

Бренд: ACERBIS Страницы: 72

Бренд: Yoshimura Страницы: 7

Бренд: Avenger Страницы: 31

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 100

Бренд: Ericsson Страницы: 44

Бренд: G PLAST Страницы: 4

Бренд: JETPRIME Страницы: 5

Бренд: Power Fist Страницы: 12

MANA GT ABS - 2009

Бренд: APRILIA Страницы: 189

Бренд: Beta Страницы: 392

Бренд: Beta Страницы: 408

Бренд: Abus Страницы: 18

Бренд: Rivco Страницы: 2

PowerParts 76512920000

Бренд: KMT Страницы: 12

Бренд: Dart Страницы: 9

Бренд: AFX Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды