KTM 2011 690 SMC AUS Скачать руководство пользователя | Manualshive

Страница: 97 / 229

background image

15

LIGHTING SYSTEM, INSTRUMENTS

95

400841-01

–

Switch on the ignition by turning the ignition key to position

ON

.

–

Press the

MODE

button repeatedly until the

TRIP 2

mode is active.

–

Keep the

SET

button pressed.

The

TRIP 2

display is set to

0.0

.

15.1.5

Setting the wheel circumference

Danger

Voiding of the government approval for road use and the insurance coverage

The vehicle is only authorized for operation on pub-

lic roads in the homologated version.

–

If the vehicle is modified in any way, it may only be used on designated tracks away from public roads. Advise the vehicle
owner and rider of this.

–

If you undertake any modifications, please insist on receiving a signed workshop order from your customer in which you
inform the customer in writing that these modifications are performed at the customer's own risk and that the vehicle will
no longer be approved for use on public roads once modified.

Condition

The motorcycle is stationary.

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the headlight mask with the headlight. (

p. 96)

302064-10

Main work

–

Unplug connector

ED

from the combination instrument.

–

Unlock pin

18

A

and remove it from connector

ED

.

–

Plug connector

ED

into the combination instrument.

–

Switch on the ignition by turning the ignition key to position

ON

.

–

Press the

MODE

button repeatedly until the

TRIP 1

display mode is active.

–

Press and hold the

MODE

button for 10 seconds.

The wheel circumference is displayed in millimeters.

302053-10

Increasing the wheel circumference

–

Press the

MODE

button

1

.

Reducing the wheel circumference

–

Press the

SET

button

2

.

–

Keep the

MODE

button and the

SET

button pressed simultaneously.

The settings are saved and the Setup menu is closed.

–

Switch off the ignition by turning the ignition key to position

OFF

.

–

Unplug connector

ED

from the combination instrument.

–

Connect pin

18

to connector

ED

.

–

Plug connector

ED

into the combination instrument.

Finishing work

–

Install the headlight mask with the headlight. (

p. 97)

–

Check the headlight setting. (

p. 96)

«
...
95
96
97
98
99
...
»

Содержание 2011 690 SMC AUS






































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 690 SMC AUS

Бренд: Yamaha Страницы: 860

MASTERFOX 125cc 2015

Бренд: d'Magna Страницы: 29

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 100

Road Star XV17AWX

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 650

Бренд: Husqvarna Страницы: 7

Бренд: Arai Страницы: 12

Бренд: Ops-Core Страницы: 20

Бренд: Ruroc Страницы: 36

Бренд: Benelli Страницы: 13

DORSODURO 1200 ABS - ATC

Бренд: APRILIA Страницы: 408

Бренд: KTM Страницы: 7

CRF50F 2004-2015

Бренд: Honda Страницы: 180

Бренд: Honda Страницы: 211

Classic 350 2019

Бренд: Royal Enfield Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды