KTM 2011 690 SMC AUS Скачать руководство пользователя | Manualshive

Страница: 90 / 229

background image

14

BRAKE SYSTEM

88

14.6

Changing the front brake fluid

Warning

Skin irritation

Brake fluid can cause skin irritation on contact.

–

Avoid contact with skin and eyes, and keep out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5
brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.

301891-10

–

Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

–

Remove screws

1

.

–

Remove cover

2

with membrane

3

.

–

Draw the old brake fluid out of the brake fluid reservoir using a syringe and fill with
fresh brake fluid.

Bleed syringe (50329050000) (

p. 210)

Brake fluid DOT 4 / DOT 5.1 (

p. 206)

302042-10

–

Pull off protection cap

4

and connect a commercially available suction device

(standard workshop equipment).

–

Release bleeder screw

5

and draw out the old brake fluid.

Info

During suction, ensure that the brake fluid reservoir is always filled with a
sufficient amount of fresh brake fluid.

–

Tighten the bleeder screw. Remove the suction device and mount the protection
cap.

100254-12

–

Add brake fluid to level

A

.

Guideline

Measurement

A

5 mm (0.2 in)

Brake fluid DOT 4 / DOT 5.1 (

p. 206)

–

Position the cover with the membrane. Mount and tighten the screws.

Info

Clean up overflowed or spilt brake fluid immediately with water.

14.7

Checking the rear brake linings

Warning

Danger of accidents

Reduced braking efficiency caused by worn brake linings.

–

Change worn brake linings immediately.

Note

Danger of accidents

Reduced braking efficiency caused by damaged brake discs.

–

If the brake linings are not changed in time, the steel brake lining carriers grind on the brake disc. The braking effect is greatly
reduced and the brake discs are destroyed. Check the brake linings regularly.

«
...
88
89
90
91
92
...
»

Содержание 2011 690 SMC AUS






































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 690 SMC AUS

Бренд: Kappa Страницы: 4

Бренд: AJP Страницы: 191

Бренд: Yoshimura Страницы: 7

Бренд: R&G Страницы: 12

Бренд: R&G Страницы: 3

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 100

Бренд: Baja motorsports Страницы: 20

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 58

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 77

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 90

Star Venture 2018

Бренд: Yamaha Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды