KTM 2011 690 SMC AUS Скачать руководство пользователя | Manualshive

Страница: 94 / 229

background image

14

BRAKE SYSTEM

92

14.12

Adding rear brake fluid

Warning

Danger of accidents

Failure of the brake system.

–

If the brake fluid level falls below the

MIN

mark, this indicates a leakage in the brake system or worn-out brake linings.

Check the brake system and do not continue riding.

Warning

Skin irritation

Brake fluid can cause skin irritation on contact.

–

Avoid contact with skin and eyes, and keep out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.

Warning

Danger of accidents

Reduced braking efficiency due to old brake fluid.

–

Change the brake fluid of the front and rear brake according to the service schedule.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5
brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.

Preparatory work

–

Check the rear brake linings. (

p. 88)

100259-10

Main work

–

Stand the vehicle upright.

–

Remove screw cap

1

with the washer and membrane

2

.

–

Add brake fluid to the

MAX

mark.

Brake fluid DOT 4 / DOT 5.1 (

p. 206)

–

Mount the screw cap with the washer and membrane.

Info

Clean up overflowed or spilt brake fluid immediately with water.

14.13

Changing the rear brake fluid

Warning

Skin irritation

Brake fluid can cause skin irritation on contact.

–

Avoid contact with skin and eyes, and keep out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Never use DOT 5 brake fluid! It is silicone-based and purple in color. Oil seals and brake lines are not designed for DOT 5
brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.

«
...
92
93
94
95
96
...
»

Содержание 2011 690 SMC AUS






































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 690 SMC AUS

Бренд: Baja motorsports Страницы: 20

Бренд: R&G Страницы: 14

Бренд: National Cycle Страницы: 2

Бренд: Braaap Страницы: 40

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 116

Tracer 9 GT 2021

Бренд: Yamaha Страницы: 126

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 87

Бренд: ICON Vehicle Dynamics Страницы: 4

Бренд: DYNATEK Страницы: 6

Бренд: Arai Страницы: 2

Ride-On Motorcycle

Бренд: Rovo Kids Страницы: 17

Бренд: Bagster Страницы: 2

F12R AIR 50 cc. - Euro 2

Бренд: Malaguti Страницы: 46

Бренд: Malaguti Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды