KTM 2011 690 SMC AUS Скачать руководство пользователя | Manualshive

Страница: 171 / 229

background image

19

LUBRICATION SYSTEM

169

19.9

Filling up with engine oil

Info

Too little engine oil or poor-quality engine oil results in premature wear to the engine.

100209-10

Main work

–

Remove filler plug with O-ring

1

from the clutch cover and add engine oil.

Engine oil

1.70 l (1.8 qt.)

Engine oil (SAE 10W/60)
(00062010035) (

p. 206)

Alternative engine
oil

Engine oil
(SAE 10W/50)

(

p. 206)

–

Refit plug with O-ring

1

and tighten it.

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may result

in unconsciousness and/or death.

–

When running the engine, always make sure there is sufficient ventila-
tion, and do not start or run the engine in an enclosed space without an
effective exhaust extraction system.

–

Start the engine and check that it is oil-tight.

Finishing work

–

Check the engine oil level. (

p. 164)

19.10

Adding engine oil

Info

Too little engine oil or poor-quality engine oil results in premature wear to the engine.

100209-10

Main work

–

Remove the oil filler plug

1

with the O-ring from the clutch cover and fill up with

engine oil.

Engine oil (SAE 10W/60) (00062010035) (

p. 206)

Engine oil (SAE 10W/50) (

p. 206)

Info

For optimal performance of the engine oil, do not mix different types of
engine oil.
If appropriate, change the engine oil.

–

Install and tighten the oil filler plug

1

with the O-ring.

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may result

in unconsciousness and/or death.

–

When running the engine, always make sure there is sufficient ventila-
tion, and do not start or run the engine in an enclosed space without an
effective exhaust extraction system.

–

Start the engine and check that it is oil-tight.

Finishing work

–

Check the engine oil level. (

p. 164)

«
...
169
170
171
172
173
...
»

Содержание 2011 690 SMC AUS






































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 690 SMC AUS

Бренд: LAZER Страницы: 6

ST400 Cruiser Edition

Бренд: STEEL HORSE AUDIO Страницы: 6

Бренд: KYMCO Страницы: 55

Бренд: Shark Страницы: 52

Бренд: Big Dog Страницы: 100

Бренд: X-lite Страницы: 84

Бренд: Memphis Shades Страницы: 2

Бренд: Pacific Helmets Страницы: 40

Montana 7 Series

Бренд: Garmin Страницы: 24

Бренд: DYNATEK Страницы: 4

Бренд: hepco & becker Страницы: 4

Black Seven 250

Бренд: Mash Страницы: 62

Бренд: Marzocchi Страницы: 116

Lectra VR24 1998

Бренд: EMB Страницы: 58

Бренд: Can-Am Страницы: 60

Бренд: KOOFU Страницы: 24

Бренд: Deco Страницы: 40

Бренд: X-TREME Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды