KTM 2011 690 SMC AUS Скачать руководство пользователя

Страница: 102 / 229

ENGINE

100

16.1

Removing the engine

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the seat. (

p. 59)

–

Disconnect the battery. (

p. 79)

–

Raise the motorcycle with the work stand. (

p. 11)

–

Take off the side cover. (

p. 60)

–

Remove the air filter box. (

p. 56)

–

Remove the manifold. (

p. 52)

–

Drain the coolant. (

p. 161)

300211-10

Main work

–

Loosen the spring-loaded band-type clamp

using the special tool. Detach the

radiator hoses.

Pliers for spring band clamp (60029057100) (

p. 212)

300212-10

–

Remove screws

300213-10

–

Remove screws

–

Take off the engine sprocket cover.

–

Remove screw

–

Take off the shift lever.

300214-10

–

Have an assistant operate the rear brake.

–

Bend up the lock washer.

–

Remove the nut of the engine sprocket with the lock washer.

–

Remove screws

300215-10

–

Remove nut

. Remove the chain adjuster.

–

Pull out the wheel spindle only far enough to allow the rear wheel to be pushed for-
ward.

–

Push the rear wheel forward as far as possible and take the chain off the rear
sprocket.

Info

The rear wheel must be fully removed.

Содержание 2011 690 SMC AUS






































































































































































































































Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды

KTM 2011 690 SMC AUS, Руководство по ремонту

Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды