KTM 2011 690 SMC AUS Скачать руководство пользователя

Страница: 20 / 229

FORK, TRIPLE CLAMP

201380-10

Warning

Danger of accidents

Reduced braking efficiency due to oil or grease on the

brake discs.

–

Always keep the brake discs free of oil and grease, and clean them with
brake cleaner when necessary.

–

Clean screw

and the wheel spindle.

–

Position the front wheel and insert the wheel spindle.

The brake linings are correctly positioned.

–

Mount and tighten screw

Guideline

Screw, front wheel spindle

M24x1.5

45 Nm
(33.2 lbf ft)

201374-11

–

Position the brake caliper and check that the brake linings are seated correctly.

–

Mount screws

spacers

but do not tighten.

–

Operate the hand brake lever repeatedly until the brake linings lie on the brake disc
and there is a pressure point. Fix the hand brake lever in the activated position.

The brake caliper straightens.

–

Fully tighten screw

Guideline

Screw, front brake caliper

M10x1.25

45 Nm
(33.2 lbf ft)

Loctite

243™

–

Remove the fixation of the hand brake lever.

–

Unload the rear of the vehicle.

–

Remove the motorcycle from the work stand. (

p. 12)

201375-11

–

Pull the front brake and compress the fork powerfully a few times.

The fork legs straighten.

–

Tighten screws

Guideline

Screw, fork stub

15 Nm
(11.1 lbf ft)

6.9

Servicing the fork

Info

These operations are the same on both fork legs.

Condition

The fork legs have been removed.

Содержание 2011 690 SMC AUS






































































































































































































































Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды

KTM 2011 690 SMC AUS, Руководство по ремонту

Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды