KTM 2011 690 SMC AUS Скачать руководство пользователя

Страница: 24 / 229

FORK, TRIPLE CLAMP

200668-10

–

Heat up the outer tube in area

of the lower sliding bushings.

Guideline

50 °C (122 °F)

–

Pull the outer tube of the fork off of the inner tube with a jerk.

Info

The lower sliding bushing

must be pulled from its bearing seat.

200658-12

–

Remove the upper sliding bushing

Info

Without using tools, carefully pull the stack apart by hand.

200659-12

–

Take off the lower sliding bushing

–

Take off support ring

–

Take off seal ring

–

Take off lock ring

–

Take off dust boot

6.11

Checking the fork legs

Condition

The fork legs have been disassembled.

200686-10

–

Check the inner tube and the axle clamp for damage.
» If damage is found:

–

Replace the inner tube.

200684-10

–

Measure the external diameter of the inner tube in several places.

External diameter of inner tube

47.975… 48.005 mm (1.88878…
1.88996 in)

» If the measured value is less than the specified value:

–

Replace the inner tube.

Содержание 2011 690 SMC AUS






































































































































































































































Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды

KTM 2011 690 SMC AUS, Руководство по ремонту

Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды