KTM 2011 690 SMC AUS Скачать руководство пользователя | Manualshive

Страница: 163 / 229

background image

18

WATER PUMP, COOLING SYSTEM

161

18.1

Draining the coolant

Warning

Danger of scalding

During motorcycle operation, the coolant gets very hot and is under pressure.

–

Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the
engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.

Warning

Danger of poisoning

Coolant is poisonous and a health hazard.

–

Coolant must not come into contact with the skin, eyes, or clothing. If contact occurs with the eyes, rinse with water imme-
diately and contact a physician. Immediately clean contaminated areas on the skin with soap and water. If coolant is swal-
lowed, contact a physician immediately. Change clothing that is contaminated with coolant. Keep coolant out of reach of
children.

600616-10

–

Stand the motorcycle upright.

–

Place a suitable container under the engine.

–

Remove screw

1

. Remove the radiator cap.

–

Completely drain the coolant.

–

Mount screw

1

with a new seal ring and tighten it.

Guideline

Plug, drain hole of water pump

M10x1

15 Nm
(11.1 lbf ft)

18.2

Filling/bleeding the cooling system

Warning

Danger of poisoning

Coolant is poisonous and a health hazard.

–

Coolant must not come into contact with the skin, eyes, or clothing. If contact occurs with the eyes, rinse with water imme-
diately and contact a physician. Immediately clean contaminated areas on the skin with soap and water. If coolant is swal-
lowed, contact a physician immediately. Change clothing that is contaminated with coolant. Keep coolant out of reach of
children.

600618-10

–

Stand the motorcycle on its side stand on a horizontal surface.

–

Remove radiator cap

1

.

600619-10

–

Refill the coolant.

Alternative 1

Coolant (

p. 206)

Alternative 2

Coolant (mixed ready to use) (

p. 206)

–

Fill the radiator completely with coolant. Mount radiator cap

1

.

«
...
161
162
163
164
165
...
»

Содержание 2011 690 SMC AUS






































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 690 SMC AUS

Бренд: Jialing Honda Страницы: 10

Scorpion Exo-T520

Бренд: Dennis Kirk Страницы: 10

Бренд: Megelli Страницы: 83

Бренд: HJC Страницы: 9

Бренд: GPX Страницы: 44

Бренд: Shark Страницы: 92

ZIEGER 10005243

Бренд: IBEX Страницы: 4

Бренд: Dakota Digital Страницы: 14

Бренд: Vanucci Страницы: 35

Бренд: Protos Страницы: 6

Бренд: KOOFU Страницы: 24

Бренд: Shark Страницы: 20

Бренд: Malaguti Страницы: 150

Бренд: RIEJU Страницы: 116

Бренд: Petzl Страницы: 3

Бренд: Petzl Страницы: 11

Бренд: Petzl Страницы: 11

Бренд: HYOSUNG Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды