KTM 2011 690 SMC AUS Скачать руководство пользователя

Страница: 127 / 229

ENGINE

125

16.4.12 Checking/measuring the cylinder

300102-10

–

Check the O-ring of the chain adjuster for damage and wear.
» If there is damage or wear:

–

Replace the O-ring.

–

Check the cylinder bearing surface for damage.
» If the cylinder bearing surface is damaged:

–

Change the cylinder and piston.

–

Measure the cylinder diameter at several places in the

and

axes using a

micrometer to check for oval wear.

–

To determine the size, measure the cylinder at a distance

from the top edge of

the cylinder.
Guideline

Distance

55 mm (2.17 in)

Cylinder - bore diameter

Size I

102.000… 102.012 mm (4.01574…
4.01621 in)

Size II

102.013… 102.025 mm (4.01625…
4.01672 in)

300103-10

–

The cylinder size

is marked on the side of the cylinder.

400376-10

–

Check the sealing area of the cylinder head for distortion using a straight edge and
the special tool.

Feeler gauge (59029041100) (

p. 212)

Cylinder/cylinder head - sealing area
distortion

≤

0.10 mm (

≤

0.0039 in)

» If the measured value does not equal the specified value:

–

Change the cylinder.

16.4.13 Checking/measuring the piston

400484-10

–

Use the special tool to measure clearance

of the piston rings in the piston ring

groove.
Guideline

Piston ring - groove clearance

≤

0.08 mm (

≤

0.0031 in)

Feeler gauge (59029041100) (

p. 212)

» If clearance

is larger than the specified value:

–

Change the piston and piston rings.

–

Check/measure the cylinder. (

p. 125)

300099-10

–

Check the piston bearing surface for damage.
» If the piston bearing surface is damaged:

–

Change the piston and, if necessary, the cylinder.

–

Check that the piston rings can move easily in the piston ring grooves.
» If the piston ring is stiff:

–

Clean the piston ring groove.

Tip

Use an old piston ring to clean the piston ring groove.

Содержание 2011 690 SMC AUS






































































































































































































































Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды

KTM 2011 690 SMC AUS, Руководство по ремонту

Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Похожие инструкции для 2011 690 SMC AUS

Бренды по названию

Популярные бренды