KTM 2011 690 SMC AUS Скачать руководство пользователя | Manualshive

Страница: 61 / 229

background image

11

FUEL TANK, SEAT, TRIM

59

11.1

Opening the filler cap

Danger

Fire hazard

Fuel is highly flammable.

–

Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

–

The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with
the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with
soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that is contaminated with fuel.
Store fuel properly in a suitable canister and keep away from children.

Warning

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to get into the ground water, the ground, or the sewage system.

100227-10

–

Lift the cover of filler cap

1

and insert the ignition key.

–

Turn the ignition key 90° counterclockwise and remove the filler cap.

Info

The filler cap has a fuel tank breather.

11.2

Closing filler cap

101070-01

–

Put the filler cap back on and turn the ignition key 90° clockwise.

–

Remove the ignition key and fold down the cover.

11.3

Removing the seat

100230-10

–

Pull on strap

1

and raise the rear of the seat at the same time.

–

Pull back the seat and lift it off.

«
...
59
60
61
62
63
...
»

Содержание 2011 690 SMC AUS






































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 690 SMC AUS

Бренд: GBRacing Страницы: 2

Бренд: yasuni Страницы: 8

Бренд: Honda Страницы: 178

Бренд: R&G Страницы: 4

Бренд: Honda Страницы: 41

Бренд: Touratech Страницы: 4

Бренд: KTM Power Parts Страницы: 12

TXT PRO - PART LIST 2005

Бренд: GAS GAS Страницы: 38

Бренд: R&G Страницы: 13

Бренд: BMW Страницы: 241

Бренд: DYNATEK Страницы: 5

Бренд: VESPA Страницы: 135

Бренд: APRILIA Страницы: 216

Бренд: ChatterBox Страницы: 10

Бренд: VM Страницы: 2

Бренд: Shark Страницы: 20

Бренд: Klarfit Страницы: 8

Бренд: Malaguti Страницы: 304

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды