KTM 2011 690 SMC AUS Скачать руководство пользователя страница 78

Страница: 78 / 229

WHEELS

1 2 3

16 17 18

400987-10

–

Pull on the upper section of the chain with the specified weight

Guideline

Weight of chain wear measurement

15 kg (33 lb.)

–

Measure distance

of 18 chain links in the lower chain section.

Info

Chain wear is not always even, so you should repeat this measurement at
different chain positions.

Maximum distance

at the longest

chain section

272 mm (10.71 in)

» If the distance

is greater than the specified measurement:

–

Change the power set.

Info

When the chain is replaced, the rear sprocket and engine sprocket
should also be changed.
New chains wear out faster on old, worn sprockets.

401170-01

–

Check the chain sliding guard for wear.
» If the lower edge of the chain pins is in line with or below the chain sliding

guard:

–

Replace the chain sliding guard.

–

Check that the chain sliding guard is firmly seated.
» If the chain sliding guard is loose:

–

Tighten the chain sliding guard.
Guideline

Screw, chain sliding
guard

8 Nm
(5.9 lbf ft)

Loctite

243™

401171-01

–

Check the chain sliding piece for wear.
» If the lower edge of the chain pins is in line with or below the chain sliding

piece:

–

Change the chain sliding piece.

–

Check that the chain sliding piece is firmly seated.
» If the chain sliding piece is loose:

–

Tighten the chain sliding piece.
Guideline

Screw, chain sliding piece

15 Nm
(11.1 lbf ft)

Содержание 2011 690 SMC AUS






































































































































































































































Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Бренды по названию

Популярные бренды

KTM 2011 690 SMC AUS, Руководство по ремонту

Результаты поиска

Содержание 2011 690 SMC AUS

Отзывы:

Бренды по названию

Популярные бренды