Kohler SFGLD360 Скачать руководство пользователя страница 237

Страница: 237 / 314

PRODUCT INFORMATION

INDEX

DATE

Dep. 2

IO-G-M-00-019e G

January 2016

MAINTENANCE OF NATURAL GAS ENGINE SFGLD

STAND-BY

3/6

1.3 Monthly maintenance

Job Interval

Job

Description

EM Monthly

(Operations to be performed with the engine stopped)

- Vent the coolant circuit. Check automatic vent valves.

- Drain condensates out of the exhaust Y-pipe

- With the dipstick, check for a possible increase of the oil level in the oil pan due to

coolant leaks

- Check the oil level of the pneumatic starter lubricator, if necessary

- Check battery acid level

- Clean the engine and its surrounding

(Operations to be carried out with the engine stabilized)

- Check coolant level / pressure. Vent circuits.

- Check oil level / pressure

- Inspect the air filter plugging level

- Check oil and coolant temperature

- Check exhaust gases temperature

- Record engine parameters on a regular basis

- Revision of the operational stability and unusual noise

- Inspect for leaks in fuel, coolant, oil and exhaust gases

1.3.1 Engine Start-up

Every month, the engine must be started and correct performance of the following items should be checked:

Start-up process and increase in speed.

Loading of the engine.

Switch: making and breaking.

The start-up test must be made with a load equal to at least 40% of the engine's rated power. The engine shall

run during a minimum of one hour.

These recommendations figure in the ISO 8528-12 standard on standby sets for security duty.

5.1.15

O&M_2.002211.810_A_10_2016

Содержание SFGLD360



























































































































































































































































































































Результаты поиска

Содержание SFGLD360

Отзывы:

Похожие инструкции для SFGLD360

Бренды по названию

Популярные бренды

Kohler SFGLD360, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SFGLD360

Отзывы:

Похожие инструкции для SFGLD360

Бренды по названию

Популярные бренды