Kohler SFGLD360 Скачать руководство пользователя страница 230

Страница: 230 / 314

PRODUCT INFORMATION

INDEX

DATE

Dep. 2

IO-G-M-00-061e C

January 2016

MAINTENANCE OF NATURAL GAS ENGINE

SFGLD 1800 RPM PRIME

3/7

ROUTINE MAINTENANCE (Type "E")

Minor Jobs

Job Interval

Job

Description

EO Daily

(Operations to be performed with the engine stopped)

- Vent the coolant circuit. Check automatic vent valves

- Drain condensates out of the exhaust Y-pipe

- Check oil pressure and temperature during the pre-lubrication phase

- With the dipstick, check for a possible increase of the oil level in the oil pan due to

coolant leaks

- Verify oil heating with the pre-heater, if necessary

- Check the oil level of the pneumatic starter lubricator, if necessary

- Clean the engine and its surrounding

(Operations to be carried out with the engine idling)

- Check oil level

(Operations to be carried out with the engine stabilized)

- Check coolant level / pressure. Vent circuits

- Check oil pressure

- Inspect the air filter plugging level (reset the pilot first)

- Check oil, coolant and exhaust gases temperature

- Check the filter cleaning state pilot of the crankcase gases recirculation system.

Control the crankcase pressure (*

- Record engine parameters on a regular basis

- Revision of the operational stability and unusual noise

- Inspect for leaks in fuel, coolant, oil and exhaust gases

5.1.7

O&M_2.002211.810_A_10_2016

Содержание SFGLD360



























































































































































































































































































































Результаты поиска

Содержание SFGLD360

Отзывы:

Похожие инструкции для SFGLD360

Бренды по названию

Популярные бренды

Kohler SFGLD360, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SFGLD360

Отзывы:

Похожие инструкции для SFGLD360

Бренды по названию

Популярные бренды