Kohler SFGLD360 Скачать руководство пользователя страница 238

Страница: 238 / 314

PRODUCT INFORMATION

INDEX

DATE

Dep. 2

IO-G-M-00-019e G

January 2016

MAINTENANCE OF NATURAL GAS ENGINE SFGLD

STAND-BY

4/6

Job Interval

Job

Description

250 h

6 months

- Analyse waste oil

- Check and refill additive level in coolant

500 h

once a year

- Change oil

KOHLER

MOTOROIL (oil sump and cooler)

- Change oil filters
- Clean the oil centrifuge filter, film-thickness measurement and change

the paper filter

- Clean the metallic sponge of the oil purifier

- Measure crankcase pressure
- Check air/fuel ratio
- Adjust

air/fuel ratio to full load (*), if necessary

- Inspect the air filters

- Adjustment of rocker arms and valve lifters. Measure valve height

- Verify the ignition timing

- Check battery and starter connections

- Inspection of

high voltage wires of the ignition system

- Change the filter of crankcase gases recirculation system and clean this circuit (*

1,500 h

3 years

- Check gas filters

- Change hoses and clamps.

- Test thermostats of coolant circuit.

- Test control and safety devices: temperature and pressure switches and probes

- Check damper temperature

- Change air filters

- Check gaskets in the rocker arm covers

- Disassemble, clean and adjust all the speed and ignition pick-ups

- Measure the exhaust back-pressure

- Change coolant

- Verify the tightening torque of knocking sensors on stud head (20 Nm)

- Check axial and Radial allowance of turbochargers

NOTE

- The spark plugs change must be made attending the IO-G-M-33-007 product information.

*It is recommended cylinder endoscope revision and compression test when the spark-plug change

- Ask

Kohler

to use another oil that it is not

KOHLER

MOTOROIL.

5.1.16

O&M_2.002211.810_A_10_2016

Содержание SFGLD360



























































































































































































































































































































Результаты поиска

Содержание SFGLD360

Отзывы:

Похожие инструкции для SFGLD360

Бренды по названию

Популярные бренды

Kohler SFGLD360, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SFGLD360

Отзывы:

Похожие инструкции для SFGLD360

Бренды по названию

Популярные бренды