Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 3

Страница: 3 / 76

981088 – September 1995

Description

Page

Table of Contents

Unpacking the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Moving the PROCESSOR to the Work Area . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the PROCESSOR on the MOUNTING STAND . . . . . . . . . . . . . . . .

Installing the PROCESSOR on a Table Top . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the PROCESSOR Through the Wall . . . . . . . . . . . . . . . . . . . . . . . . .

Changing the PROCESSOR to 50 or 60 Hz Operation, M43 and M43A Only . . . . . . . . .

Installing the Alternate SPROCKET on an M43 or M43A PROCESSOR Only

Changing the Input CONNECTOR on the DRIVE MOTOR . . . . . . . . . . . . . .

Processor Setup Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Available Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Changing the PROCESSOR Setup Options . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the DRYER PLENUM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the RACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Identifying the Parts of the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the WASH RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the FIXER and DEVELOPER RACKS . . . . . . . . . . . . . . . . . . . . . . .

Installing the DRYER RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Leveling the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Making the Necessary Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking the Electrical Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Requirements for European Installations of the M43 PROCESSOR . .

Making the Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting the DRAIN LINES and the Water Supply HOSE

for the Table Top or MOUNTING STAND Installations . . . . . . . . . . . . . . . . . . . .

Connecting the HOSES from the REPLENISHMENT TANKS

in Table Top or MOUNTING STAND Installations . . . . . . . . . . . . . . . . . . . . . . .

Doing the Water Leak Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting the Developer Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking and Adjusting the Replenishment Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the KNOBS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the KNOBS on the DRAIN VALVES . . . . . . . . . . . . . . . . . . . . . . . .

Installing the DRYER TEMPERATURE CONTROL KNOB . . . . . . . . . . . . .

Installing the FEED TRAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the LIGHTTIGHT FEED TRAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Filling the TANKS with the Developer and Fixer Solutions . . . . . . . . . . . . . . . . . . . . . . .

Mixing the Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Filling the FIXER TANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Filling the DEVELOPER TANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Final Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking for Correct Operation of the PROCESSOR . . . . . . . . . . . . . . . . . . . .

Transport Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting the Dryer Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды