Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 71

Страница: 71 / 76

Filling the TANKS with the Developer and Fixer Solutions

981088 – September 1995

[6] Pour more developer solution into the DEVELOPER TANK until the level of the solution reaches the top of

the STEP in the DEVELOPER TANK.

[7] Remove the SPLASH GUARD. Rinse and store it near the PROCESSOR.

Caution

Wet ENTRANCE ROLLERS of the DEVELOPER and FIXER RACKS can cause artifacts.

[8] Very carefully, install the DEVELOPER RACK into the DEVELOPER TANK. You can identify the

DEVELOPER RACK by the red WIRE TIE.

• Be careful not to splash any developer solution into the FIXER TANK.

– Small amounts of developer solution in the FIXER TANK will not seriously contaminate the fixer

solution, but will degrade it.

• Check that the DEVELOPER RACK is seated firmly in the DEVELOPER TANK.

[9] Check that the DRIVE GEARS on the DEVELOPER and FIXER RACKS correctly engage the GEARS on the

MAIN DRIVE SHAFT.

[10] Check that the level of the solution in the DEVELOPER TANK is at the top of the OVERFLOW WEIR.

If necessary, add more solution. See Figure 61 on Page 70.

[11] Install the developer EVAPORATION COVER between the DEVELOPER RACK and the FIXER RACK.

Position the EVAPORATION COVER on the TIE RODS of the 2 RACKS as shown.

Figure 62

Installing the Developer EVAPORATION COVER

H130_0139HA

WIRE TIE

DRIVE SHAFT

GEAR

H130_0139HCB

EVAPORATION
COVER

FIXER RACK

DEVELOPER
RACK

OVERFLOW
WEIR

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды