Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 5

Страница: 5 / 76

Unpacking the PROCESSOR

981088 – September 1995

Section 1: Unpacking the PROCESSOR

Figure 1

Removing the Components

[1] Cut the metal bands, open the shipping carton, and

remove any packing material.

Important

When removing protective packing material or
wrapping from components, be careful not to cut
through the protective wrapping and damage the
component.

[2] Remove the items packed with the PROCESSOR.

See publication 1C7052 in the front pocket of
your publications binder for a list of the items
packed with your PROCESSOR model.

[3] Remove:

• shipping carton from around the

PROCESSOR

• any other packing materials

• TOP COVER from the PROCESSOR

• EVAPORATION COVERS for the

DEVELOPER and FIXER RACKS

• 2 SIDE ACCESS PANELS and the BACK

ACCESS PANEL by loosening the
2 SCREWS securing each PANEL

• POWER CABLE (provided with the M43A

only)

H130_0140CA

COVER (2)

EVAPORATION

GUARD

SPLASH

FEED
TRAY

H130_0140CCA

DRYER RACK

metal

bands

PANEL

BACK

ACCESS

TOP

COVER

carton

shipping

SIDE ACCESS
PANEL (2)

EXIT ROLLER

ASSEMBLY

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Бренды по названию

Популярные бренды

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Бренды по названию

Популярные бренды