Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 67

Страница: 67 / 76

Filling the TANKS with the Developer and Fixer Solutions

981088 – September 1995

Section 15: Filling the TANKS with the Developer and Fixer Solutions

Mixing the Chemicals

Warning

Wear rubber gloves, safety glasses, and protective clothing when mixing chemicals and filling the TANKS.

Important

• When mixing chemical solutions, follow all instructions and precautions on the labels of the chemical bottles.

• Mix only a 2-week supply of developer replenisher.

[1] Following all directions provided with the chemicals, mix at least 19 litres (5 gallons) of replenisher.

[2] Before adding fresh chemicals to an empty PROCESSOR, check that the developer and fixer DRAIN VALVES

are fully closed. The DRAIN VALVE KNOBS should be pushed in and rotated

⁄

turn.

Figure 58

Closing the DRAIN VALVES

H130_0019BA

PANEL

DISPLAY

DRAIN VALVES

H130_0019BCA

FEED TRAY

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды