manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Поделиться
Скачать
Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 23

Installing the PROCESSOR

981088 – September 1995

23

Installing the GASKET on the WOOD FRAME

[41] Cut the foam GASKET to fit around the edges of the hole cut in the WOOD FRAME for the PROCESSOR.

[42] Install the GASKET on the PROCESSOR side of the WOOD FRAME around the perimeter of the hole.  See

the figure for the correct location of the GASKET.

[43] Check that there are no gaps in the GASKET.

[44] Cut another piece of GASKET the dimension of the front of the PROCESSOR.

[45] Install the GASKET on the PROCESSOR along the bottom edge of the FRONT ACCESS PANEL.

Important

Additional GASKETS may be necessary in some installations:

• where the wall is not plumb

• if using a LIGHTTIGHT FEED TRAY

Figure 18

Installing the GASKETS

H130_0197HA

installed

when

GASKET

of

Position

WOOD FRAME

GASKETS

H130_0197HCA

FRONT ACCESS

PANEL

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды