Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 32

Страница: 32 / 76

INSTALLATION INSTRUCTIONS

September 1995 – 981088

Section 3: Changing the PROCESSOR to 50 or 60 Hz Operation, M43 and

M43A Only

Important

• Clinic 1 PROCESSORS cannot be installed in 50 Hz sites. There is no 50 Hz SPROCKET for the Clinic 1

PROCESSOR. If you are installing a Clinic 1 PROCESSOR, advance to the “PROCESSOR Setup Options”
section on Page 35.

• All Kodak X-Omat M43A PROCESSORS and Kodak X-Omat Clinic 1 PROCESSORS are set up for 115 V AC,

60 Hz operation only.

• If you are installing an M43A PROCESSOR into a 50 Hz site, you will need to switch the SPROCKET on the

MAIN DRIVE MOTOR, and switch the input CONNECTOR on the DRIVE MOTOR.

• All Kodak X-Omat M43 PROCESSORS are set up for 230 V AC, 50 Hz operation.

• If you are installing an M43 PROCESSOR into a 60 Hz site, you will need to switch the SPROCKET on the

MAIN DRIVE MOTOR, and switch the input CONNECTOR on the DRIVE MOTOR.

Figure 27

Identifying the 2 SPROCKETS

H130_0167HA

CONNECTORS

50 Hz SPROCKET

20-TOOTH

60 Hz SPROCKET

16-TOOTH

H130_0167HCA

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Бренды по названию

Популярные бренды

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Бренды по названию

Популярные бренды