Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 19

Страница: 19 / 76

Installing the PROCESSOR

981088 – September 1995

[23] Connect the 3 DRAIN HOSES to the 3 DRAIN VALVE FITTINGS.

(a) Position the CLAMPS, provided in the prepack, so that you can access the SCREWS by inserting a

SCREWDRIVER through the notches in the BRACKET.

(b) Insert the 3 DRAIN HOSES under the 3 NARROW BAND CLAMPS and tighten the 3 SCREWS of the

CLAMPS.

Figure 13

Connecting the DRAIN HOSES

[24] For an M43 PROCESSOR only, install the HOSE ADAPTER and WASHER packed with the PROCESSOR

to the bottom of the WATER INPUT SOLENOID.

[25] Use a standard 5/8 in. NHT HOSE BIB FITTING to connect the HOSE from the main water supply to the under

side of the WATER INPUT SOLENOID.

Note

If you are routing a water supply HOSE under the PROCESSOR, you will need a 90

fitting, not provided, at the

WATER INPUT SOLENOID connection.

Figure 14

Connecting the DRAIN HOSES and the HOSE from the Main Water Supply

H130_0187BA

DRAIN VALVE
FITTING (3)

H130_0187BCA

DRAIN

developer

HOSE

SCREW (3)

BRACKET

DRAIN

wash

HOSE

CLAMP (3)

NARROW BAND

DRAIN
HOSE

fixer

H130_0026BA

fixer DRAIN HOSE

wash DRAIN HOSE

water supply HOSE

developer DRAIN HOSE

BIB FITTING

SOLENOID

WATER INPUT

H130_0026BCB

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Бренды по названию

Популярные бренды

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Бренды по названию

Популярные бренды