Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 54

Страница: 54 / 76

INSTALLATION INSTRUCTIONS

September 1995 – 981088

Section 9: Doing the Water Leak Test

[1] If SEISMIC BRACKETS are needed and if the PROCESSOR is in its final position, install the SEISMIC

BRACKETS at this time. See the instructions provided with the SEISMIC BRACKET KIT 261413.

[2] Check that all 3 DRAIN VALVES are closed.

[3] Fill the FIXER and DEVELOPER TANKS with water until the level of the water is at the OVERFLOW

WEIRS. Water will go down the DRAIN LINES when the TANKS are full.

Caution

To prevent spills or splashes into other TANKS or onto electrical parts:

• Check that the SIDE ACCESS PANELS are installed.

• Pour the water into the TANK at the non-drive end of the PROCESSOR.

• Do not pour water onto the RACKS.

Figure 46

Filling the TANKS for the Water Leak Test

H130_0152HA

H130_0152HCA

DEVELOPER
TANK

OVERFLOW

FIXER TANK

WEIRS

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды