Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 58

Страница: 58 / 76

INSTALLATION INSTRUCTIONS

September 1995 – 981088

Section 10: Setting the Developer Temperature

[1] Insert a calibrated THERMOMETER TL-1582 into the DEVELOPER TANK and measure the temperature of

the developer solution.

(a) If the temperature is 33.9

0.3

C (93

⁄

F), go to section “Checking and Adjusting the

Replenishment Rates” on Page 60.

(b) If the temperature is not 33.9

0.3

C (93

⁄

F), continue with this procedure.

Possible damage from electrostatic discharge.

ESD

[2] Pull out the SUPPORT SHELF for the ELECTRICAL BOX from the drive side of the PROCESSOR.

[3] Pull out the ELECTRICAL BOX.

[4] Connect your ESD protective wrist strap into the ESD JACK on the ELECTRICAL BOX.

[5] Open the COVER of the ELECTRICAL BOX. Fasten the COVER open by placing the O-RING, that is on the

PROCESSOR TANK, around the POST on the COVER.

Figure 50

Pulling Out the ELECTRICAL BOX

H130_0143HA

BOX

ELECTRICAL

SUPPORT SHELF

ELECTRICAL
BOX

JACK

O-RING

POST

COVER

100 CIRCUIT BOARD

H130_0143HCA

ESD

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Результаты поиска

Содержание HEALTH SCIENCES X-Omat Clinic 1

Отзывы:

Похожие инструкции для HEALTH SCIENCES X-Omat Clinic 1

Бренды по названию

Популярные бренды